863 EMD Restoration
Re: 863 EMD Restoration
The only 'babes ' I drive around now are the grandchildren. They don't seem to notice that I am old and quite unattractive.
- A40FARINAGURU
- Posts: 16413
- Joined: Tue Mar 30, 2010 8:14 am
- Committee Role: A35 Registrar
- Location: Birmingham (Home of the Austin)
- x 21
Re: 863 EMD Restoration
SteveClem wrote:The only 'babes ' I drive around now are the grandchildren. They don't seem to notice that I am old and quite unattractive.
Nick Bayliss
Club's A35 (Saloon) Registrar, South Midlands Area Contact
Email, a35@austina30a35ownersclub.co.uk
Connected with A30/A35's for 63 years
A30/A35 Member A1372 (since 1981)
Club's A35 (Saloon) Registrar, South Midlands Area Contact
Email, a35@austina30a35ownersclub.co.uk
Connected with A30/A35's for 63 years
A30/A35 Member A1372 (since 1981)
-
- Posts: 4933
- Joined: Wed Apr 29, 2009 11:03 pm
- Location: Sheffield
Re: 863 EMD Restoration
Ran EMD yesterday and the Zenith Carb has developed a leak. I knew about this a while ago bit it was slight now it was getting too much
Took off the float chamber the two screws and noticed the cork gasket I had made, which I thought was the answer to the fuel leaks and air leaks into the carb,had perished and came off in crumbs as I rubbed it off with my fingers SEE PHOTO.
The float chamber also had some fine "carp" in there which you can see and I cleaned it out. i TOOK OFF THE EMULSION BLOCK PIECE and I made a new gasket out of my fairly thick gasket card material, (NOT CORK) fitted that with some gasket blue sealant and some liberally around the chamber mating face to the main carb body to prevent air leakage into the venturi and refitted to the carb
May road test tomorrow
John G
Took off the float chamber the two screws and noticed the cork gasket I had made, which I thought was the answer to the fuel leaks and air leaks into the carb,had perished and came off in crumbs as I rubbed it off with my fingers SEE PHOTO.
The float chamber also had some fine "carp" in there which you can see and I cleaned it out. i TOOK OFF THE EMULSION BLOCK PIECE and I made a new gasket out of my fairly thick gasket card material, (NOT CORK) fitted that with some gasket blue sealant and some liberally around the chamber mating face to the main carb body to prevent air leakage into the venturi and refitted to the carb
May road test tomorrow
John G
- Attachments
-
- CARP IN FLOAT CHAMBER + CORK GASKET IN CRUMBS
- 20170306_175715.jpg (217.42 KiB) Viewed 1049 times
-
- PERISHED SELF MADE CORK GASKET
- 20170306_175452.jpg (103.73 KiB) Viewed 1049 times
John (Tight Yorkshireman)
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
- A40FARINAGURU
- Posts: 16413
- Joined: Tue Mar 30, 2010 8:14 am
- Committee Role: A35 Registrar
- Location: Birmingham (Home of the Austin)
- x 21
Re: 863 EMD Restoration
hope you get it sorted
Nick Bayliss
Club's A35 (Saloon) Registrar, South Midlands Area Contact
Email, a35@austina30a35ownersclub.co.uk
Connected with A30/A35's for 63 years
A30/A35 Member A1372 (since 1981)
Club's A35 (Saloon) Registrar, South Midlands Area Contact
Email, a35@austina30a35ownersclub.co.uk
Connected with A30/A35's for 63 years
A30/A35 Member A1372 (since 1981)
-
- Posts: 4933
- Joined: Wed Apr 29, 2009 11:03 pm
- Location: Sheffield
Re: 863 EMD Restoration
Should be ok now Nick! Will run it tomorrow if weathers not too bad
John G
John G
John (Tight Yorkshireman)
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
-
- Posts: 5896
- Joined: Mon Apr 21, 2008 1:00 pm
- Location: High Wycombe, Bucks
Re: 863 EMD Restoration
John, if that blue sealant is the one I think it is it will not stand up to fuel for long.
You need a setting sealant like the old Hermetite brown stuff.
You need a setting sealant like the old Hermetite brown stuff.
-
- Posts: 4933
- Joined: Wed Apr 29, 2009 11:03 pm
- Location: Sheffield
Re: 863 EMD Restoration
Ohhh didnt realise, however Ive used a thin smidging on the faces to assist but fingers crossed the new gasket will sort itDave Clark wrote:John, if that blue sealant is the one I think it is it will not stand up to fuel for long.
You need a setting sealant like the old Hermetite brown stuff.
Have used the sealant in a larger amount as a an attempt to make up the likely difference of the mating faces of float chamber to the main carb body rather tham a sealant gainst fuel leakages
John G
John (Tight Yorkshireman)
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
-
- Posts: 4933
- Joined: Wed Apr 29, 2009 11:03 pm
- Location: Sheffield
Re: 863 EMD Restoration
Took EMD out again today and on a dual carriageway acording to the speedo it was 70mph. It was wavering at 65 to 67 ish but when increasing speed was firm against the 70mph max on the clock. Its fairly accurate at at around 40 mph I know that, but does anyone have an opinion of what the speed would have probably been rather than 70,....or was it 70mph?
John G
John G
John (Tight Yorkshireman)
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
Re: 863 EMD Restoration
Hi John,
Good going! Main factors to consider are speedo head, diff ratio and tyre size (taking into account wear too). Easiest way is to instead just watch the speed on a sat nav.
Chris T.
Good going! Main factors to consider are speedo head, diff ratio and tyre size (taking into account wear too). Easiest way is to instead just watch the speed on a sat nav.
Chris T.
400,000+ A30 miles in 40 years
Austins <=> sustAin
Austins <=> sustAin
-
- Posts: 4933
- Joined: Wed Apr 29, 2009 11:03 pm
- Location: Sheffield
Re: 863 EMD Restoration
Yeah ChrisChris T wrote:Hi John,
Good going! Main factors to consider are speedo head, diff ratio and tyre size (taking into account wear too). Easiest way is to instead just watch the speed on a sat nav.
Chris T.
Didnt have it with me but will do at some point, just fishing for any general thoughts
Thanks
John G
John (Tight Yorkshireman)
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
-
- Posts: 4933
- Joined: Wed Apr 29, 2009 11:03 pm
- Location: Sheffield
Re: 863 EMD Restoration
Came to adjust the brakes on EMD tonight and I have the moggy fronts set up. One of the snail cam screw heads just broke off just by twisting with the screwdriver through the small access holes. No mean torque by any length. This is the standard of quality we have to endure. These were new on the renovation and guess Ive only adjusted them twice before
Carp!
John G
Carp!
John G
- Attachments
-
- BROKEN SCREW SECTION
- Broke.jpg (54.5 KiB) Viewed 809 times
-
- THIS IS WHAT THE HEAD SHOULD BE
- Screwhead.jpg (38.68 KiB) Viewed 809 times
-
- BROKEN BITS
- Bits.jpg (84.26 KiB) Viewed 809 times
John (Tight Yorkshireman)
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
First referred to as the Tight Yorkshireman in editions of the Clubs Spotlight: Autumn 1996 Page 40 and Autumn 1997 Page 15
-
- Posts: 5896
- Joined: Mon Apr 21, 2008 1:00 pm
- Location: High Wycombe, Bucks
Re: 863 EMD Restoration
As with so many reproduced parts it is often better to try to get old used ones in reasonable condition.
These items at least are OK to use secondhand.
These items at least are OK to use secondhand.
- gazza82
- Site Admin
- Posts: 5585
- Joined: Sun Nov 24, 2013 3:39 pm
- Committee Role: WebEditor
- Location: Buckinghamshire
- x 2
- x 17
- Contact:
Re: 863 EMD Restoration
It's not just classics this happens to. I replaced the rear discs on my daughter's Peugeot 206CC a couple of years ago and the disc-to-hub mounting screws were missing. These are short countersunk philips screws. I know you don't really need these as the wheel holds them on, but I do like to do the job properly. So I bought a new set of 4 from Peugeot. First one I screwed in snapped off leaving the thread jammed in the hub! Second one was ok. Same happened on the other side although it was the 2nd one I fitted! So unless the factory used too different threads (unlikely) the quality of the screws was dubious to say the least.
"If you're driving on the edge ... you're leaving too much room!"
Club WebEditor.
Cars: "Project 757" '59 A35 2-door bought in 1971 & Subaru BRZ SE LUX Auto plus "family fleet": Alfa MiTo, Peugeot 206, (Ex '98 Alfa Romeo 156 2.0 TS)
Club WebEditor.
Cars: "Project 757" '59 A35 2-door bought in 1971 & Subaru BRZ SE LUX Auto plus "family fleet": Alfa MiTo, Peugeot 206, (Ex '98 Alfa Romeo 156 2.0 TS)
- A40FARINAGURU
- Posts: 16413
- Joined: Tue Mar 30, 2010 8:14 am
- Committee Role: A35 Registrar
- Location: Birmingham (Home of the Austin)
- x 21
Re: 863 EMD Restoration
Dave Clark wrote:As with so many reproduced parts it is often better to try to get old used ones in reasonable condition.
These items at least are OK to use secondhand.
Nick Bayliss
Club's A35 (Saloon) Registrar, South Midlands Area Contact
Email, a35@austina30a35ownersclub.co.uk
Connected with A30/A35's for 63 years
A30/A35 Member A1372 (since 1981)
Club's A35 (Saloon) Registrar, South Midlands Area Contact
Email, a35@austina30a35ownersclub.co.uk
Connected with A30/A35's for 63 years
A30/A35 Member A1372 (since 1981)
-
- Posts: 1035
- Joined: Wed Dec 24, 2008 8:59 pm
- Location: Rotherham, South Yorks
- x 3
Re: 863 EMD Restoration
Hi John
If you're desperate and and they will fit I have a few Mk 1 A40 Farina ones you can have.
Give me a call 079077 057111, but I', off to Hibalstow about 10am tomorrow.
Cheers
Phil
If you're desperate and and they will fit I have a few Mk 1 A40 Farina ones you can have.
Give me a call 079077 057111, but I', off to Hibalstow about 10am tomorrow.
Cheers
Phil
Phil Harrison
El Presidente' 2013 - 2016 (Now Retired)
Membership Secretary - Retired
Archivist in the dim and distant past - Retired
Chair or 2009 / 2015 Nat Rally Comm
Sunny Rotherham!!
El Presidente' 2013 - 2016 (Now Retired)
Membership Secretary - Retired
Archivist in the dim and distant past - Retired
Chair or 2009 / 2015 Nat Rally Comm
Sunny Rotherham!!